Hoe word die TPS op die TB45E enjin korrek ingestel?

Post Reply
Patrol At
Newbie
Newbie
Posts: 2
Joined: 08 Jul 2017 21:09
Full Name: Jan van Wyk
Nickname: Patrol At
Home Town: Upington
Current 4x4: '99 Patrol 4.5 SUV
Home Language: Afrikaans
Been thanked: 1 time

Hoe word die TPS op die TB45E enjin korrek ingestel?

Post by Patrol At » 12 Nov 2017 20:17

Ek doen tans voorkomende onderhoud op my "99 4.5 GRX Patrol. Skynbaar is daar fyn verstelling rondom die "fast idle cam" die TPS ea.
Kan iemand dalk raad gee of help?
Is daar enigiets behalwe hitte en 'n skielike stamp soos om die sensor te laat val, wat 'n "Knock sensor" kan breek?

User avatar
ChristoSlang
Patrolman
Patrolman
Posts: 869
Joined: 07 Apr 2009 16:54
Full Name: Christo van Rensburg
Nickname: ChristoSlang
Home Town: Pretoria, ZA
Current 4x4: Nissan 4.2 GL Patrol
Home Language: Afrikaans
Location: Garsfontein, Pretoria
Has thanked: 5 times
Been thanked: 71 times

Re: Hoe word die TPS op die TB45E enjin korrek ingestel?

Post by ChristoSlang » 13 Nov 2017 19:43

Op my 350z is daar 'n "pedal dance" wat mens gebruik om die TPS se idle air volume van voor af te leer. Wetie of daar iets soortgelyks is vir die TB45E nie?

Hier's die stappe in die korrekte volgorde - dalk is dit dieselfde vir ander Nissan ECUs ook. As dit nie werk nie sal dit hopelik nie skade doen nie...

1. Accelerator Pedal Release Position Learning
Make sure that the accelerator pedal is fully released.
• Turn ignition switch ON and wait at least 2 secs.
• Turn ignition switch OFF wait at least 10 secs.
• Turn ignition switch ON and wait at least 2 secs.
• Turn ignition switch OFF wait at least 10 secs.

2. Throttle Valve Closed Position Learning
Make sure that accelerator pedal is fully released.
• Turn ignition switch ON.
• Turn ignition switch OFF wait at least 10 secs.
NB: Make sure that the throttle valve moves during above 10 secs by confirming the operating sound.

3. Idle Air Volume Learning (Throttle Position Learning)
NB: Perform previous two procedures 1st!
• Start engine and warm it up to normal operating temperature.
• Turn ignition switch OFF and wait at least 10 secs.
• Conform that accelerator pedal is fully released, turn ignition switch ON and wait 3 secs.
• Repeat the following procedures quickly five times within 5 secs:
• Fully depress the accelerator pedal (HARD)
• Fully release the accelerator pedal.
• Wait 7 sec, fully depress accelerator pedal and keep it in for approx. 20 secs until the Check Engine Light (CEL) stops blinking & stays ON.
• Fully release the accelerator pedal within 3 secs after the CEL is ON.
• Start engine and let it idle.
• Wait 20 secs, then rev up the engine two or three times and make sure the idle speed and ignition timing are within the specifications.
Christo (the snake man)
1998 4.2 GL Patrol (Chuck Norris)
2007 350Z twin-turbo coupe (Batmobile)
Image

Post Reply

Return to “13. Electrical & Electronics”

Who is online

Users browsing this forum: No registered users and 0 guests