Madman / Landy on line

User avatar
SJC
Patrolman 1000+
Patrolman 1000+
Posts: 2516
Joined: 23 Nov 2014 14:20
Full Name: SJC
Nickname: Fanus
Home Town: Lowveld
Current 4x4: 4.2TD Pickup & 4500 GRX
Home Language: Afrikaans/English
Has thanked: 75 times
Been thanked: 103 times

Re: Madman / Landy on line

Post by SJC » 16 Jan 2016 21:04

Die pressure sender wat ek het is 10 bar.

User avatar
Pieter B
Senior Member
Senior Member
Posts: 194
Joined: 29 Sep 2014 12:40
Full Name: Pieter Botha
Nickname: Pieter
Home Town: Alberton
Current 4x4: '02 Nissan Hardbody 3.3
Home Language: Afrikaans
Been thanked: 10 times

Re: Madman / Landy on line

Post by Pieter B » 17 Jan 2016 19:30

Die sender was 'n 10bar sover ek kan onthou. Die pressure op die 2.7 was so tussen 3 en 4 as ek reg onthou. Maak net seker van die thread op jou blok en die thread van die sender. Op daai sender het ek daai adapter stukkie gekry om dit te maak pas. Die 2 punte op die sender was 'n 1 wat na die madman gaan en die ander een was vir die oorspronklike konneksie. Dus sal jou dash oliedruk liggie ook nog werk

User avatar
SJC
Patrolman 1000+
Patrolman 1000+
Posts: 2516
Joined: 23 Nov 2014 14:20
Full Name: SJC
Nickname: Fanus
Home Town: Lowveld
Current 4x4: 4.2TD Pickup & 4500 GRX
Home Language: Afrikaans/English
Has thanked: 75 times
Been thanked: 103 times

Re: Madman / Landy on line

Post by SJC » 18 Jan 2016 07:07

djhep wrote:Hi all. Im just reading this thread now.
SAC in Boksburg did a good job tuning my Patrol recently, and i am happy with the work they did.......
However they also routed the earth wire to the cab chassis, causing erratic readings while operating lights, a/c etc.
They also fitted the oil pressure sensor incorrectly, causing it to drip oil at a rate fast enough to give my chassis a nice corrosion protection layer on my 300k journey home.

It was fairly simple to correct both problems, but i would expect them to get this basic bread and butter installation done correctly.

Or maybe i am just too fussy :sad:

Dave
No you are not too fussy.

I just hope my installer will get it right.

User avatar
SJC
Patrolman 1000+
Patrolman 1000+
Posts: 2516
Joined: 23 Nov 2014 14:20
Full Name: SJC
Nickname: Fanus
Home Town: Lowveld
Current 4x4: 4.2TD Pickup & 4500 GRX
Home Language: Afrikaans/English
Has thanked: 75 times
Been thanked: 103 times

Re: Madman / Landy on line

Post by SJC » 18 Jan 2016 07:34

Michael wrote:Fanus, die oil pressure sender moet die 10bar een wees
Die sump plug adaptor is dieselfde as die cruiser 4.2 sin, so kyk onder die cruiser Madman kit watse een hy gebruik.
Jy sal moet jou top radiator hose meet om te sien watse een jy moet koop, ek het geraai en toe koop ek doe verkeerde een
Ek het nog nie kans gehad om te meet nie, maar volgens die ouens op aussie patrol forum is die binne diameter aan radiator kant 34mm. Sal ek dan die 35mm adaptor kit moet koop?

Wat het mens nodig om coolant level te meet?

User avatar
Michael
Moderator
Posts: 2436
Joined: 05 Mar 2014 14:39
Full Name: Michael
Nickname: Steyn
Home Town: Centurion
Current 4x4: Patrol GU 4.2 Turbo Diesel
Home Language: Afrikaans
Location: Centurion, PTA
Has thanked: 139 times
Been thanked: 220 times

Re: Madman / Landy on line

Post by Michael » 18 Jan 2016 08:39

Jy gaan daai water pyp in die middel deur moet sny en daai water level adaptor daar in sit. Mak net seker jou water pyp is nie groodter waar hy op die radiator gaan nie.

Jy het niks nodig nie, als is daar. Jy moet net die water temp sender by koop wat in skroef in daai adaptor. :thumbup:
"The Just shall live by Faith" Rom1:17

Check out my build here My Patrol
And my engine rebuild here mostly engine related stuff

User avatar
SJC
Patrolman 1000+
Patrolman 1000+
Posts: 2516
Joined: 23 Nov 2014 14:20
Full Name: SJC
Nickname: Fanus
Home Town: Lowveld
Current 4x4: 4.2TD Pickup & 4500 GRX
Home Language: Afrikaans/English
Has thanked: 75 times
Been thanked: 103 times

Re: Madman / Landy on line

Post by SJC » 19 Jan 2016 08:43

Die waterpyp se omtrek is 150mm, die pyp se wande is 4-5mm.
So volgens my berekininge sal die binneste deursnee, afhangende van die pyp se wande 37.75-39.75 wees.

Hoop my formule is reg. :think:

C=Pi x d
or d = C/Pi
150/3.14159 = 47.747 (buite deursnee)..

Ek sal dan maar gaan vir 38cm adaptor kit...

User avatar
Peter Connan
Moderator
Posts: 4930
Joined: 10 Sep 2010 07:21
Full Name: Peter Connan
Nickname: Piet
Home Town: Kempton Park
Current 4x4: 1996 Patrol 4.2SGL
Home Language: Afrikaans
Location: Kempton Park
Has thanked: 186 times
Been thanked: 266 times

Re: Madman / Landy on line

Post by Peter Connan » 19 Jan 2016 17:15

Jou formule is reg, maar dis nie altyd baie akkuraat om so te werk nie.

Kan jy nie die pyp op die thermostat housing meet nie?
Mag ons ons kenniskry met lekkerkry aanhoukry.

User avatar
SJC
Patrolman 1000+
Patrolman 1000+
Posts: 2516
Joined: 23 Nov 2014 14:20
Full Name: SJC
Nickname: Fanus
Home Town: Lowveld
Current 4x4: 4.2TD Pickup & 4500 GRX
Home Language: Afrikaans/English
Has thanked: 75 times
Been thanked: 103 times

Re: Madman / Landy on line

Post by SJC » 19 Jan 2016 17:51

Ek het die pyp se omtrek met 'n maat band gemeet, dis presies 150mm. Nee ek het nie die deursnee gemeet nie.
(Is nie lus om die pyp te diskonnekteur nie...)

User avatar
Peter Connan
Moderator
Posts: 4930
Joined: 10 Sep 2010 07:21
Full Name: Peter Connan
Nickname: Piet
Home Town: Kempton Park
Current 4x4: 1996 Patrol 4.2SGL
Home Language: Afrikaans
Location: Kempton Park
Has thanked: 186 times
Been thanked: 266 times

Re: Madman / Landy on line

Post by Peter Connan » 19 Jan 2016 19:25

SJC wrote:Ek het die pyp se omtrek met 'n maat band gemeet, dis presies 150mm.
Dis waarvoor ek bang was. Maatband werk nie hiervoor nie, omdat hy konveks gebuig isle hy nie plat teen die pyp nie.

Gebruik eerder 'n stukkie lyn, en meet hom dan met 'n maatband of lineaal. As jy dit doen, kan jy hom voor die punt van die rubberpyp om die thermostat housing wen, en so kan jy een berekening uitskakel.
Mag ons ons kenniskry met lekkerkry aanhoukry.

User avatar
SJC
Patrolman 1000+
Patrolman 1000+
Posts: 2516
Joined: 23 Nov 2014 14:20
Full Name: SJC
Nickname: Fanus
Home Town: Lowveld
Current 4x4: 4.2TD Pickup & 4500 GRX
Home Language: Afrikaans/English
Has thanked: 75 times
Been thanked: 103 times

Re: Madman / Landy on line

Post by SJC » 19 Jan 2016 20:24

Nee, dis een van daai "maatbande" wat die tannies wat kleure maak gebruik... hy vou heeltemal om die pyp.
Attachments
51f9cnKx90L._SY300_.jpg
51f9cnKx90L._SY300_.jpg (17.63 KiB) Viewed 347 times

Post Reply

Return to “13. Electrical & Electronics”

Who is online

Users browsing this forum: Bing [Bot] and 0 guests